The Mustang Forum for Track & Racing Enthusiasts

Taking your Mustang to an open track/HPDE event for the first time? Do you race competitively? This forum is for you! Log in to remove most ads.

Register Log in
  • Welcome to the Ford Mustang forum built for owners of the Mustang GT350, BOSS 302, GT500, and all other S550, S197, SN95, Fox Body and older Mustangs set up for open track days, road racing, and/or autocross. Join our forum, interact with others, share your build, and help us strengthen this community!

Recent content by zlalomz

  1. Extended studs for Magneride Mustangs

    Another data point. My GTPremium had a build date of 11/21.

  2. Extended studs for Magneride Mustangs

    Fabulous info I have not seen anywhere. THANK YOU. I have purchased spacers off your site but missed this. The silent roll out and no mention of these hubs on other vendor sites has been most frustrating.

  3. Steeda Adj. Swaybar Endlinks Autocrosser

    Following Steeda directions, is this string alignment going to the correct points to adjust for parallel? Also with the camber plates moved to the -3 degree area for 19x11 305 30 19(haven't measured camber yet) the zerk fitting was tearing into the metal brake lines. I removed it and...

  4. No Hammer Splined Strut Bolt Install

    That’s what the guy tried on the other forum with no success. Give it a go and see if you can make it work.. Also the ball joint press can usually be rented for cheap.

  5. No Hammer Splined Strut Bolt Install

    The nut is removed and flipped over to give a bigger surface for the press. Not really needed though.

  6. No Hammer Splined Strut Bolt Install

    Yes, both removal and install easily. I posted on another forum and a member used this which is smaller and much cheaper. He used a 1 1/4 socket as the spacer the bolt is pushed through. OEMTOOLS 27023 Ball Joint Press

  7. No Hammer Splined Strut Bolt Install

    Here’s a video of a new one being installed, the stud tool is just flipped around. A spacer that came with the tool, was needed to press out the lower bolt. I have a 4 bolt hub in my 2021. Similar to a magneride hub.

  8. No Hammer Splined Strut Bolt Install

    I was replacing my struts. To remove the two splined bolts, all I’ve seen on videos is a sledge hammer used to pound out the bolts. I found using this stud press removed the bolts much quicker and easier (judging by the videos I have watched). I bought 4 new bolts from Ford to replace the one...

  9. No Hammer Splined Strut Bolt Install

    I just checked Amazon and the price has jumped $250 since March. I guess build one from a c-clamp… Ouch. OTC 4295 Wheel Stud Service Kit https://www.amazon.com/dp/B009B2M3YO?ref=ppx_pop_mob_ap_share

  10. No Hammer Splined Strut Bolt Install

    I couldn’t stand the idea of a sledge used on my new Mustang, so I sprung for a large truck stud removal tool. Super easy removal and install. I did start to build a c-clamp/ socket contraption similar to this but I ran into getting enough clearance on the inside and outside of my socket. I...

  11. Extended studs for Magneride Mustangs

    Thanks. This is what I was hoping to hear.

  12. Extended studs for Magneride Mustangs

    I have a 2021 GT Non-Magneride but it has the Magneride style front hub that Ford switched over to in May 2021 (I read on a forum). My dilemma is this. I have a Ford Perf hub for earlier spindle steering knuckles, with the elusive ARP long studs.I was hoping to bolt them on but what a surprise...
See more
Top