The Mustang Forum for Track & Racing Enthusiasts

Taking your Mustang to an open track/HPDE event for the first time? Do you race competitively? This forum is for you! Log in to remove most ads.

  • Welcome to the Ford Mustang forum built for owners of the Mustang GT350, BOSS 302, GT500, and all other S550, S197, SN95, Fox Body and older Mustangs set up for open track days, road racing, and/or autocross. Join our forum, interact with others, share your build, and help us strengthen this community!

Full Stainless 3" Exhaust w/Side-pipes pics

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Sesshomurai

Finally got around to photo'ing my exhaust for folks to see. Here is the parts list, enjoy:

Full longtube, off-road, 3" stainless steel exhaust system with controllable sound and replaceable mufflers (Kooks over-axle mufflers are welded so those weren't used here)
  • Over-axles http://www.jpcracing.com/over-the-axle-pipes/
  • Side pipes http://www.lethalperformance.com/2012-2013-boss-mustang-302/exhaust/side-pipes.html
  • Long tubes http://www.cooltechllc.com/Boss/Boss_KO_Hdr.shtml
  • Off-road H-pipe http://www.cooltechllc.com/Boss/Boss_KO_HPipeBossNoCat.shtml
  • Header Wrap http://www.summitracing.com/parts/the-11022/overview/
  • Mufflers http://www.americanmuscle.com/ford-gt500-axleback-2011gt.html
  • Header Paint http://www.summitracing.com/parts/the-12001?gclid=CO-u0cmPvrQCFQyk4AodLAUAsw
  • QTP Electric Cutouts http://www.quicktimeperformance.com/302/index.php

exhaust-1.jpg

exhaust-2.jpg

exhaust-3.jpg

exhaust-4.jpg

exhaust-5.jpg

exhaust-6.jpg

QTP Electric exhaust cutouts. A must have for no-cat, 3" longtubes with side pipes. You can control the opening amount and get just the right sound.
Also, good for tracks that have noise restrictions.
exhaust-7.jpg

exhaust-8.jpg

exhaust-9.jpg

exhaust-10.jpg

exhaust-11.jpg

Spray painted my muffler tips with black high-temp exhaust paint for a matte black finish. I like it.
exhaust-12.jpg

exhaust-13.jpg


The wide-open sound can be heard in this dyno pull. Everyone had to wear ears. However, this was with sides open and muffler deletes.
[youtube]
http://www.youtube.com/watch?v=-IBFlDtxbK8
[/youtube]
 

Sesshomurai

steveespo said:
Nice job Darren. See you at VIR for Superfest Memorial Day weekend?
Steve

Definitely! Look forward to it. Who's hosting that event by the way?
 

Sesshomurai

I had it dyno'd on a superflow which uses a vastly different metric than a dynojet (which I am scheduling to get done soon). My tuner computed the BHP to be over 500, so in the range of 50-60hp. I will collate the dyno charts and post them after I get the dynojet one done.
 

Sesshomurai

CaliMR said:
Did you have any issues with fitment on the side pipes? I remember a thread here about how they didn't fit right.

Yeah, there was some minor fitment issues with the side pipes. I think they have a slight design flaw, but it wasn't a hard fix. I just mounted them under the rocker first and then got the bolts through them on the h-pipe and ratcheted them into alignment. Also had to weld a tiny strip of steel to close the mount bracket bolt hole on the side pipe so it wouldn't slip out.

However, my ground clearance underneath the side pipes is now only 3". Gotta make sure my bump stops don't overshoot that mark.
 

TMO Supporting Vendors

Top