S197 WTB:

[Short circuit]

Hello

All the parts I been looking for has been located or bought. Thanks all. I will update this thread if I need anything else.

Thank you

 

[Short circuit]

This is for a street car. Stock kit will be perfect. Thanks

 

[SVT Rider]

You can buy the 4-piston Brembo set for around $700 new. The Brembo's use the same lines as the factory S197 calipers, and you would need to buy the 14" rotors. I can provide part numbers to buy new if you would like.

 

[RodS197]

These are for sale up here in Salt Lake (not mine, just following on the local classified site). Looks like lines and calipers. For rotors, I would go buy some Duralast Gold units at Autozone. They are a high carbon content rotor and I run them on all my street vehicles. The track car is special and gets Girodisc

Another good source is Kohr Motorsports.

2008 Shelby GT 500 Brembo Front Calipers

$450.00 2008 Shelby GT 500 Brembo Front Calipers for sale in Sandy, UT on KSL Classifieds. View a wide selection of Race Car Parts and other great items on KSL Classifieds.

classifieds.ksl.com

 

[steeda5]

I have this complete set up. Im in PHX,AZ area.
Brian

 

[Short circuit]

These are for sale up here in Salt Lake (not mine, just following on the local classified site). Looks like lines and calipers. For rotors, I would go buy some Duralast Gold units at Autozone. They are a high carbon content rotor and I run them on all my street vehicles. The track car is special and gets Girodisc

Another good source is Kohr Motorsports.

2008 Shelby GT 500 Brembo Front Calipers

$450.00 2008 Shelby GT 500 Brembo Front Calipers for sale in Sandy, UT on KSL Classifieds. View a wide selection of Race Car Parts and other great items on KSL Classifieds.

classifieds.ksl.com

Thanks, I will look into this.

 

[Short circuit]

What is the difference between the 05-10 front struts vs 11-14, I believe rear shocks are the same???

Thanks

 

[Short circuit]

Looking for caster camber plates as well. I believe caster camber plates needs to be 05-10 specific by MM.

 

[Robert Valente]

I have completely rebuilt Baer 6P Calipers and essentially new rotors. They would require mounting brackets only. New, they were quite expensive, but you could have them for $250.

Baer Pro+ 6P FRONT Street/Sport Brake System for S197 Mustang

The Pro+ 6P two-piece caliper is Baer's most trusted offering and machined out of billet aluminum. The 6P line represents Baer's best cost versus value for an aggressive road offering, that also suitable for many levels of track use.

kennybrown.com

 

[Short circuit]

That's one hell of a deal. But unfortunately, I found the calipers and parts I needed. Thank you for posting.

 

[KazarS197]

I have completely rebuilt Baer 6P Calipers and essentially new rotors. They would require mounting brackets only. New, they were quite expensive, but you could have them for $250.

Baer Pro+ 6P FRONT Street/Sport Brake System for S197 Mustang

The Pro+ 6P two-piece caliper is Baer's most trusted offering and machined out of billet aluminum. The 6P line represents Baer's best cost versus value for an aggressive road offering, that also suitable for many levels of track use.

kennybrown.com

PM'd

 

[Dave Bowman]

Hello

I am searching for OEM Ford front 4 piston Brembo brakes. I Would like to purchase complete set up including calipers, rotors and lines.

Thank you

 

[Dave Bowman]

Here you go. Brembo‘s with 14k miles on them, new seals and new titanium shims,new 14“ zinc coated slotted rotors and new Hawk ceramic pads. $1000.00 delivered