Welcome to the Ford Mustang forum built for owners of the Mustang GT350, BOSS 302, GT500, and all other S550, S197, SN95, Fox Body and older Mustangs set up for open track days, road racing, and/or autocross. Join our forum, interact with others, share your build, and help us strengthen this community!
You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
Just read the spec sheet on this car.
I'm thinking this is going to be a really small build thread. That thing is fully built already. Damn that's a list.
I'll just wait for the posts in the track videos 😁
Not quite today but Sunday-Installed 3.73 gears, T2 Torsen and 1 piece aluminum driveshaft into my 2014 V6 as well as some regular track prep, new pads, rotor scuff and put 1L of brake fluid through the system!
Impressive run in a 4 popper Duane. The car looks great and you are laying down some impressive times with a car that is not supposed to be the top choice for D Street - I am impressed!
All I have is an occasional Spec Miata race and some autocross runs these days... I did pilot a 2020 Mustang Ecoboost in street class to an FTD/FTP at the local autocross club this past weekend, thoughMe vs the V8 that ran 3rd raw/2nd pax...
Hi everyone! I'm a new forum member located in northeast Tennessee. I'm a grandfather to 4 little ones and have fully embraced my mid-life crisis! I've owned many Mustangs through the years, and currently have a 2024 Dark Horse. I'm a member...
Alright here is what yall have been waiting for. First TA event. It went well. Placed 4th out of 17 cars in a ultra competitive class. Grid Life Street mod. Basically the whole weekend time qualifies you for a podium sprint. Top 5 times go into...
Yeah I was thinking TOB. But it could be your trans too. Did you replace the TOB? Have you lost any brake fluid? Does pumping the clutch help?Good luck. Hope it's just air in the lines or TOB. If there is or was a leak I think that can cause...
I'm a rules weenie, and my interpretation is that "the occupant" does not use the 3-bar clip to "adjust the size of the assembly" -- the 3-bar clip is what the installer uses to fit the assembly to the vehicle. An occupant (someone sitting in a...
Kinda strange situation. Private property and all that kinda thing.
Well my other suggestion still stands. Over the sides of the seat at the hinge point and down to the lap mount locations. Going straight under has a tendency to crush the family...
I have been accused more than once of spending other peoples money so I guess what goes around comes around. I just finished reading fab mans 267 page post and it was enlightening for what can be accomplished and scary for my pocket book. Funny...
Great looking Beast and all it needs now is a decal on the side for " TrackMustangsOnline , " ha! Do you run the CS in Time Trials or just use for fun whipping up on C5 Vettes?
Gotcha. I have seen people complain about it but I’ve never experienced it personally.Pagid RST3/GLOC R12 has worked great for me. Also squeezing the brake instead of stabbing it like Steve mentioned
I know it's not a direct fit you need a proper aftermarket ECU to use it properly and who knows what else. Which is why I solved that issue for me by going back to OEM rear pads.
Gotcha. I have seen people complain about it but I’ve never experienced it personally.Pagid RST3/GLOC R12 has worked great for me. Also squeezing the brake instead of stabbing it like Steve mentioned (see full post)
I know it's not a direct fit you need a proper aftermarket ECU to use it properly and who knows what else. Which is why I solved that issue for me by going back to OEM rear pads.
Look forward to seeing all you guys at the Mustang Roundup this August and it is so cool for a well respected Mustang Aftermarket Company to get out and meet so many of their customers at the track!!!